The best pressure gauges, compared.
Top pick: Hansfelds 63 mm, 0–6 bar, rear – Highest score in the set: class 1.6, glycerin, and a rear G1/4 BSP stem on a 0–6 bar scale. The part number is shared with the bottom-mount listing. Best value: Innfeeltech 40 mm, 0–14 bar – About £7.99, with a BSP 1/8 inch stem the attribute agrees with, bushings and PTFE, and no fault sentence in the file. A 0–200 psi scale is coarse for low mains pressure. Updated October 2026.
A pressure gauge shows how hard a fluid pushes, in bar or psi. In the UK you buy one for mains pressure at a tap, a compressor dial, or tyres cold against the placard. A suitable pressure gauge matches that one job. Range, thread, mount, and the parts the fluid touches still apply when the models change. As a rule of thumb, use about three quarters of full scale if the pressure is steady, and about two thirds if it pulses. Do not read the bottom tenth, or past the last mark. BSP parallel thread seals on a washer. BSPT and NPT seal on the taper. A reducer changes size only. Bottom, back, or side entry has to face you. Brass internals suit fluids that do not attack brass. Liquid in the case damps vibration and is not a tighter accuracy class. Keep it off oxygen and other strong oxidisers. A garden-tap reading is not the water company's communication-pipe test, and the needle is not a safety valve. Those checks are in the [pressure gauge buying guide](/hub/measuring-equipment/pressure-gauge/sub/pressure-gauge-buying-guide).
A pressure gauge shows how hard a fluid pushes, in bar or psi. In the UK you buy one for mains pressure at a tap, a compressor dial, or tyres cold against the placard. A suitable pressure gauge matches that one job.
42 products checked · 61 hrs invested · +17,300 readers
Swipe for more
1-2 of 12
Personal buying guide
Question 1 of 2
Where does it connect?
The Hansfelds rear-mount gauge reads 0–6 bar on a 63 mm glycerin-filled dial at £15.95, with class 1.6 and a G1/4 BSP brass connection. Across 91 amazon.co.uk ratings the line is 4.7, and four of the captured texts are marked United Kingdom. Those notes are short praise, including one buyer who fitted it on a solar hot-water system. The box includes 3/8 inch and 1/2 inch brass reducers and a roll of PTFE tape. The part number ssglincrimpeddualscaleSSGSBACK is the same code printed on the bottom-mount 0–10 bar listing, so the number does not tell you which way the stem points. The range line also says 0–6 bar/psi and does not print a separate psi end figure. Glycerin is there to damp a pulsing needle, and the listing does not describe the gauge as oxygen-clean or safety-pattern. It is the top pick in this set when you want a stated class 1.6, glycerin, and a rear G1/4 BSP stem, and you can tell the mount from the title.
Pros
Cons
Best for: You want a rear-entry 0–6 bar watch on a pulsing water or air line, and the port is G1/4 BSP or a size the reducers reach.
Less suitable: A bottom-entry port, oxygen or another strong oxidiser, or a job that needs the part number to prove the mount.
Specifications
Common questions
Is the mount at the back?
This title says rear G1/4 BSP. The part number is the same as B0C1ZNLDM5, whose title says bottom connection.
What does accuracy 1.6 refer to?
The listing prints 1.6. It does not include a calibration certificate. It does not say the figure is a percentage of the reading. BS EN 837-1 treats class 1.6 as a percentage of the span.
Does the listing confirm gas use?
It asks whether the gauge can be used for gas monitoring and does not answer. The applications bullet lists industrial, hydraulic, pneumatic, cooling, and water.
The Hansfelds bottom-mount gauge is a 63 mm glycerin-filled dial at £15.95, marked 0–10 bar with class 1.6 and a G1/4 BSP brass stem. The amazon.co.uk line is 4.7 from 75 ratings. Five of 31 captured texts are marked United Kingdom, and none of those five describes a product fault. One UK buyer says it seals tight on the threads, and another says the thread was wrong for their port and that the mismatch was their mistake. Brass reducers for 3/8 inch and 1/2 inch, plus PTFE tape, are in the box. The part number matches the rear-mount 0–6 bar listing, so you cannot use that code to confirm a bottom stem. A bullet writes 0-10 bar/psi and does not give a separate psi full-scale figure.
Pros
Cons
Best for: Your port takes a bottom G1/4 BSP stem and the working pressure sits inside a 0–10 bar scale.
Less suitable: A rear-entry panel, a vacuum job, or oxygen service.
Specifications
Common questions
Is this the bottom-entry version?
The title and a bullet say bottom G1/4 BSP. The part number matches the rear-connection listing B0C59HWMCY.
Are reducers and tape included?
Yes. The package line lists two brass reducers, 3/8 and 1/2 inch, and PTFE tape.
What do the UK reviews say?
Five UK reviews call it good quality. One says it sealed on the threads. One says the thread did not match their port, and that this was their mistake. No fault of the gauge is described.
The JIVTO gauge is a 2.5 inch liquid-filled dial at £10.36, with a 1/4 inch BSPT lower mount and a stated medium limit of 60 °C. The title gives 0–100 psi and 0–7 bar, while a bullet writes 0-100 psi/bar, which is not the same pair of figures. IP67 is stated, the case bullet says stainless steel with a polycarbonate lens, and the material attribute says brass. The amazon.co.uk line is 4.7 from five ratings. The only captured review is marked United Kingdom and says the pressure works OK, which is too small a sample for a fault pattern. The fluid in the case is not named, no accuracy class is stated, and the included-components line is absent. The listing points it at hydraulic and pulsing machinery, which is a different duty from a garden-tap check.
Pros
Cons
Best for: You want a lower-mount liquid-filled 1/4 inch BSPT dial for a pulsing line inside 7 bar, and you accept a five-review sample.
Less suitable: A garden-tap test, a buyer who needs the fill fluid named, or anyone who reads the 0-100 psi/bar bullet as 100 bar.
Specifications
Common questions
Is the fill glycerin?
The listing says liquid filled and does not name the fluid.
Which range is printed?
The title says 0–100 psi and 0–7 bar. One bullet says 0–100 psi/bar. Both lines are in the listing.
How many UK reviews are in the file?
One. It says the pressure works OK. There is no fault sentence.
The GERUI Y50 is a pair of side-connection dials at £8.99, each offered as 0–10 bar or 0–150 psi. The title says 40 mm and a bullet says 52 mm, and the thread is described as 1/4 inch while the attribute line says 1/4 inch NPT. Across 175 amazon.co.uk ratings the line is 4.5. Seven captured texts are marked United Kingdom. Buyers report a clear dial on an incoming water supply, and two UK reviews say the needle was detached on one gauge of the pair. A UK buyer had to add PTFE because the thread arrived with no seal, and turned it into a 1/2 inch tee with an adaptor. The case is sheet steel, the movement is brass, and the stated temperature is −20 °C to +70 °C. A case, tape, or reducer is not listed in the box.
Pros
Cons
Best for: You want a spare pair for a side 1/4 inch port and you will inspect the needle and add your own seal.
Less suitable: A single watch with a stated class, a port you already know is BSP only, or a buyer who needs one dial diameter.
Specifications
Common questions
How many gauges are in the order?
The listing says two items. UK reviews describe one of the two arriving with the needle detached.
What size is the dial?
The title says 40 mm. A bullet says 52 mm. Both figures are printed.
Is the thread NPT?
The attribute line says 1/4 inch NPT. The title says 1/4 inch and does not name the form. A UK buyer called it a plain thread and added PTFE.
Thermometer World’s tester is a 50 mm dial at £11.95, scaled 0–11 bar and 0–160 psi, with 3/4 inch and 1/2 inch BSP tap connectors. Across 244 amazon.co.uk ratings the line is 4.4, and the first 50 captured texts are marked United Kingdom. Several buyers say it fitted a tap without leaking, and one says water stayed out of the gauge body after two earlier gauges had let water out. Another UK review describes a gush at the tap coupling on both outside taps, and that unit was returned. The material attribute says plastic, no accuracy class is stated, and the page asks about a hose without printing a length. A 2-year warranty is stated.
Pros
Cons
Best for: You want a BSP hose-tap check on a 0–11 bar scale and you can return it if the nut will not seal.
Less suitable: A compressor port, a tyre valve, or a job that needs a stated accuracy class.
Specifications
Common questions
Does the listing include a hose length?
It asks whether a hose is included and does not print a length. The included-components line says one water pressure gauge, and the bullets describe a 3/4 and 1/2 inch BSP tap connector.
Is an accuracy class stated?
No. The bullets say the readings are precise and do not give a class such as 1.6.
What do the UK reviews say about leaks?
Several say it fitted a tap without leaking. One says it gushed at the tap coupling on both outside taps and was returned. Accuracy is not vouched for in the reviews.
This Innfeeltech gauge is a 40 mm radial dial at £7.99, marked 0–7 bar and 0–100 psi, sold with bushings to 1/4 inch, 3/8 inch and 1/2 inch and PTFE tape. The title says BSP 1/8 inch and the attribute line says BSPT, so the thread form is not settled on the page. The amazon.co.uk line is 4.4 from 60 ratings, and six captured texts are marked United Kingdom. Those UK notes do not describe a leak: one buyer fitted it as a compressor replacement, and another uses it to control an airbrush compressor. A separate UK line objects to manufacture in China rather than to a reading. No accuracy class is stated, and glycerin is not named.
Pros
Cons
Best for: Your compressor port is 1/8 inch, you can confirm BSP or BSPT before you seal it, and the working pressure sits inside 7 bar.
Less suitable: A buyer who needs the listing to name one thread form, a garden tap, or a tyre valve.
Specifications
Common questions
Is the thread BSP or BSPT?
The title says BSP 1/8 inch. The attribute line says BSPT. The listing does not resolve that.
What did UK reviews use it on?
An air compressor, with no leak reported by that buyer, and an airbrush compressor. Six UK reviews do not describe a failed gauge.
Is a fill stated?
No. Glycerin is not named.
This Innfeeltech gauge is a 50 mm axial dial at £7.99, marked 0–7 bar and 0–100 psi, with a title connection of BSP 1/4 inch. The box lists bushings to 3/8 inch and 1/2 inch, a hex nipple to 1/8 inch, and PTFE tape. The attribute line says Sechskant rather than a thread form, so the thread claim and the attribute do not match. The amazon.co.uk line is 4.4 from 38 ratings. One captured text is marked United Kingdom, and that buyer says the item had been used, was faulty, and was sent out again. The other captured lines are short and are not marked United Kingdom. No accuracy class is stated, and glycerin is not named.
Pros
Cons
Best for: You need an axial 0–7 bar dial on a BSP 1/4 inch port and you will reject a unit that arrives looking used.
Less suitable: A radial mount, a buyer who treats the attribute line as the thread form, or a first gauge you cannot inspect on arrival.
Specifications
Common questions
Where does the thread leave the case?
The title says axial. It is not the radial style used on the 40 mm Innfeeltech gauges.
What does the thread attribute say?
Sechskant. That word is not BSP, BSPT, or NPT. The title says BSP 1/4 inch.
What is the only UK review?
The buyer says the gauge had been used, was faulty, and was sent out again.
The AA AADTP is a plastic digital tyre gauge at £8.49, scaled 0–100 psi and 6.85 bar, with a blue back-lit screen and automatic shut-off. Across 7,312 amazon.co.uk ratings the line is 4.3, and the first 50 captured texts are marked United Kingdom. Reviewers like a clear psi or bar figure, including one buyer whose compressor gauge had gone past the placard. The same file returns to a chuck that is hard to seat, so air leaves before the reading settles, and to a battery cover held by tiny screws. The psi and bar legend is called minuscule for long sight. An attribute line says NPT, which the bullets do not explain and the reviews do not use as a pipe thread. The question about bicycle tyres is unanswered, and the stated ceiling is 100 psi.
Pros
Cons
Best for: You check car tyres cold against the placard and the figure sits inside 100 psi.
Less suitable: A bicycle that needs more than 100 psi, a BSP compressor port, or a gauge you want to recharge as a pack.
Specifications
Common questions
Does it fit a pipe thread?
The product is a tyre gauge. Reviews describe a tyre valve. The attribute line says NPT and the bullets do not explain that word.
Can it read a bicycle tyre?
The listing asks and does not answer. The stated ceiling is 100 psi / 6.85 bar.
What do UK reviews complain about?
Tiny screws on the battery cover, difficulty sealing on the valve so air is lost, and a very small psi/bar legend. Others praise the backlight and the reading.
Uharbour’s tester screws onto a 3/4 inch or 1/2 inch tap and shows 0–11 bar and 0–160 psi on a 2 inch dial, at £11.20. The listing states chrome-plated brass BSPT nuts, a braided hose, and a rubber protector, and it says thread-seal tape is not in the box. Across 348 amazon.co.uk ratings the line is 4.3, and 31 of the first 50 captured texts are marked United Kingdom. Buyers use it on an outside tap, and some add their own adapters for a kitchen tap or a shower. The repeated complaint is a leak unless the nut is tightened with a wrench, and several people say they have not checked the number against another instrument. One title calls the tool flimsy, and the listing tells you to keep it dry and out of direct rain. No accuracy class is printed.
Pros
Cons
Best for: You want the tap tester in this set that states brass BSPT nuts, and you will tighten the nut until it seals.
Less suitable: A permanent compressor port, a tyre valve, or a fitting you will only ever nip up by hand.
Specifications
Common questions
Is thread tape in the box?
No. The listing says to use thread-seal tape and says it is not included.
What do reviews say about leaks?
UK reviews include leaks unless the nut is tightened with a wrench, a blocked hose, and a call for a better washer. Others say it read an outside tap easily.
Does it state an accuracy class?
No. Several reviewers say they cannot vouch for accuracy against another gauge.
This Innfeeltech dial is a 40 mm radial gauge at £7.99, marked 0–14 bar and 0–200 psi, with a BSP 1/8 inch stem. The box adds bushings to 1/4 inch, 3/8 inch and 1/2 inch, and a piece of PTFE tape. The amazon.co.uk line is 4.3 from 45 ratings. Three captured texts are marked United Kingdom, and the file has no fault sentence. One UK buyer says the connectors suited a compressor and calls the price good value. There is no accuracy class, and the application line mentions vibration without saying the case is glycerin-filled. On a 0–200 psi scale a reading near 2 bar sits close to the bottom of the dial, which is a coarse place to judge a low mains pressure. It is the best value in this set: the same score as Uharbour, at a lower shelf price, and the 0–7 bar radial sibling is the same £7.99 with a BSP against BSPT conflict.
Pros
Cons
Best for: You are replacing a compressor or pump gauge on a BSP 1/8 inch port, or a size the bushings reach, and the working pressure sits well up a 0–14 bar scale.
Less suitable: A garden-tap check around a low mains figure, a tyre valve, or a line that needs a stated class 1.6.
Specifications
Common questions
Is it glycerin filled?
The listing does not say so. It mentions vibration and pulsation without naming a fill.
What is the thread?
BSP 1/8 inch, radial, with bushings up to 1/2 inch and PTFE tape named in the title.
What did UK buyers use it for?
One fitted it to a compressor and noted the connectors and PTFE tape. The three UK reviews do not describe a fault.
Stowberry’s tester is a 50 mm dial at £11.95, scaled 0–11 bar and 0–160 psi, with a stated 300 mm hose and a 3/4 inch and 1/2 inch hose-tap connector. Across 258 amazon.co.uk ratings the line is 4.2, and the first 50 captured texts are marked United Kingdom. Buyers use it on an outside tap before an electric shower or a garden watering system, and one sealed a leak with PTFE tape on the tap thread. The repeated complaint is a soft plastic nut, a washer that sits flush, and water at the blue ring. The attribute line says GHT, while the bullets describe a hose-tap connector, and the material attribute says stainless steel even though the reviews describe a plastic nut. A 2-year warranty is stated. There is no accuracy class.
Pros
Cons
Best for: You want a short hose on an outside tap and you will check the nut and washer before you trust the seal.
Less suitable: A tap that needs a brass BSPT nut, a permanent pipe port, or a listing whose thread attribute matches the bullets.
Specifications
Common questions
Is the connector BSP?
The bullets say a standard 3/4 and 1/2 inch hose-tap connector. The attribute line says GHT. Those are not the same claim.
Do the reviews mention the plastic fitting?
Yes. UK reviews call the nut soft, say the washer sits flush, and describe leaks at the blue ring. One buyer stopped a leak with PTFE tape.
Does it claim a tools-free fit?
Yes. The bullets say no tools, connect and read. A review says the fitting is for a garden tap, not the end of a hosepipe.
This Innfeeltech gauge is a 50 mm radial vacuum dial at £7.99, scaled from −1 to 0 bar and −14 to 0 psi, with a BSP 1/4 inch connection. Bushings to 3/8 inch and 1/2 inch, and a hex nipple down to 1/8 inch, are named in the title. The case is stated as 304 stainless steel with brass inside. The amazon.co.uk line is 3.8 from 46 ratings, the lowest stars in this set. One captured text is marked United Kingdom, and that buyer says both units they tried leaked: about 0.2 bar per second on one and about 0.1 bar per minute on the other. No accuracy class is stated. The scale is vacuum, so a positive compressor pressure is the wrong duty for this dial.
Pros
Cons
Best for: You already need a −1 to 0 bar reading on a BSP 1/4 inch port and you can check the joint for a leak before you trust the needle.
Less suitable: A positive air or water pressure, a tyre valve, or a vacuum hold that must stay tight.
Specifications
Common questions
Will this read compressor pressure?
No. The range is −1 to 0 bar. It is a vacuum gauge, not a positive-pressure dial.
What does the UK review say?
The buyer tried two. One leaked about 0.2 bar per second. The other leaked about 0.1 bar per minute.
Is tape included?
The title does not list PTFE tape. The included-components line says one pressure gauge.
Twelve pressure-gauge listings on amazon.co.uk were scored from the listing and the review notes on file, not from a lab test. The method caps Amazon stars at 30 points, review count at 20, and listing fit at 30. Listing fit splits into accuracy class (10), connection (8), range (6), readout (4) and fittings (2). Those three blocks are weighted 38, 25 and 37 below so the weights total 100. Shelf price is not in the score. It decides the best value. Deductions apply for a thin review sample, a repeated leak, a detached needle or a used faulty arrival, and a part number shared with a listing whose title states a different mount. A thread conflict already scored down on connection is not deducted again. The score does not prove a stated class, and a garden-tap reading is not Ofwat’s communication-pipe test.
Amazon stars
38%Up to 30 points in the method, (stars ÷ 5) × 30. No star line scores 0. The star line stays the amazon.co.uk figure. Shown here as 38 so the three blocks total 100.
Review count
25%Up to 20 points in the method: log10 of the review count, times 7, rounded half up, and capped at 20. No reviews scores 0. Shown here as 25 so the three blocks total 100.
Listing fit
37%Up to 30 points in the method. Class 1.6 stated scores 10, otherwise 0. Connection scores 8 when the thread or tyre valve is named and the title agrees with the attribute, or 4 when they conflict. Range scores 6 when both ends agree, or 3 when a bullet states a different pair. Readout scores 4 for one dial size or a digital display, or 2 when the diameter disagrees. Fittings score 2 when reducers, tape, a tap connector, a hose, or a complete tyre gauge is in the box. Shown here as 37 so the three blocks total 100.
Start with the job, then the range, then the thread and the mount, then the wetted parts and the fill. The notes below follow that order for these twelve listings. None of the scores is a laboratory test.
A pressure gauge in this UK shopper set is a Bourdon-tube dial for a pipe or a compressor, a short-hose tester for a garden tap, or a handheld digital gauge for a tyre valve. People buy one to see mains pressure before a shower or an irrigation job, to replace a compressor dial, or to check tyres cold against the placard. Quality is the match of range, thread, and wetted parts to that one job.
A 0–11 bar hose tester, a G1/4 compressor dial, a tyre chuck, and a −1 to 0 bar vacuum gauge are different tools. A reducer changes size only. It does not change the job.
Glycerin damps vibration. Class 1.6, where it is printed, is ±1.6 per cent of span. The fill does not raise that class, and it must not be used on oxygen or other strong oxidisers.
The Hansfelds titles disagree on mount and share one part number. The GERUI title says 40 mm, a bullet says 52 mm, and the attribute says NPT. Stowberry’s attribute says GHT while the bullets say a hose-tap connector.
Name the job before the brand. A hose tester, a permanent dial, a tyre gauge, and a vacuum gauge do not stand in for each other. Stewarts’ guidance puts a steady pressure near 75 per cent of full scale, and a fluctuating one near 65 per cent. Do not judge a low value in the bottom tenth, and do not go past the last mark. BSP parallel seals on a washer. BSPT and NPT seal on the taper. Bottom, back, and side entry have to face you. Brass internals are for fluids that do not attack brass.
Read dial size, class, fittings, and temperature from the listing. If the title and the attribute disagree, keep both. In this set only the two Hansfelds gauges print class 1.6, and neither includes a UKAS certificate. Shelf prices here run from £7.99 to £15.95. The best value is the £7.99 Innfeeltech 0–14 bar dial, because the thread lines agree and Uharbour’s matching score costs £11.20. A 0–200 psi scale is coarse for low mains pressure.
Three typical situations, each with a recommendation from this comparison.
You want a hose tester on a 0–11 bar scale, not a compressor port. Uharbour states brass 3/4 inch and 1/2 inch BSPT nuts and a braided hose, at about £11.20, with 4.3 from 348 reviews. UK reviews describe leaks unless the nut is tightened with a wrench, and thread-seal tape is not in the box.
You want a stated class on a glycerin-filled dial. The Hansfelds rear-mount gauge is about £15.95, class 1.6, 63 mm, rear G1/4 BSP, with 4.7 from 91 reviews. Reducers and PTFE tape are in the box. The part number is shared with the bottom-mount listing.
You want a valve gauge, not a BSP port. The AA digital tyre gauge is about £8.49, scaled 0–100 psi and 6.85 bar, with 4.3 from 7,312 reviews. Reviews describe a chuck that loses air before it seats. The stated ceiling is 100 psi.
In this set of twelve amazon.co.uk listings, the top pick is the Hansfelds 63 mm rear-mount gauge at about £15.95. It states class 1.6, a glycerin fill, and a rear G1/4 BSP stem on a 0–6 bar scale, with 4.7 from 91 reviews. The part number is shared with the bottom-mount 0–10 bar listing, so the title, not that code, tells you which way the stem points. The best value is the Innfeeltech 40 mm 0–14 bar dial at about £7.99, 4.3 from 45, with a BSP 1/8 inch stem the attribute agrees with, plus bushings and PTFE tape. Uharbour also scores 58, at about £11.20, and loses on price. A 0–200 psi dial is a coarse way to read a low mains pressure, and there is no accuracy class. None of these scores is a lab test.
Hansfelds 63 mm, 0–6 bar, rear
Highest score in the set: class 1.6, glycerin, and a rear G1/4 BSP stem on a 0–6 bar scale. The part number is shared with the bottom-mount listing.
Innfeeltech 40 mm, 0–14 bar
About £7.99, with a BSP 1/8 inch stem the attribute agrees with, bushings and PTFE, and no fault sentence in the file. A 0–200 psi scale is coarse for low mains pressure.
Editorial
Peter F. is the editor for DIY & tools at productscompared.co.uk. Comparisons in this category are checked against amazon.co.uk listings, review evidence and public UK sources.
Guides on what to look for, how to use a product, and common mistakes.
Public UK sources from the research digest. Shelf prices and star lines are the amazon.co.uk figures captured with these twelve listings. The price bands are this set, not a market average.
This page contains affiliate links to amazon.co.uk. If you buy through them, we may earn a commission at no extra cost to you. Prices, stars and review counts are the amazon.co.uk figures captured with these twelve listings. We did not lab-test these pressure gauges.
