The best magnetic stove fans, compared.
Top pick: Drcokars HL-600A chimney fan Best value: Drcokars HL-600A – Highest price-against-evidence block at about £31.99, with UK magnet comments and a printed 12–15.5 cm pipe band. Updated 22.10.2026.
A magnetic stove fan clamps to the outside of a single-wall connecting fluepipe and pushes room air. You use one when the stove top is cool, small, sloped, soapstone or crowded, and when a fridge magnet sticks to the cold pipe. Tell quality by a magnetic hot pipe, a module whose top face stays cooler, and reviews that are actually about a pipe mount. Only the and the have UK texts that clearly describe a flue clamp. Whether any pipe fan fits this stove is in the [magnetic stove fan buying guide](/hub/fireplaces-and-stoves/magnetic-stove-fan/sub/magnetic-stove-fan-buying-guide). A magnetic stove fan is a pipe-clamped, heat-powered room-air fan. It does not sit in the flue gas. A mechanical chimney fan that moves flue gas is draught equipment. The British and Association says combustion products must still leave if that fan fails. A stovetop fan needs a flat hot plate and cooler air from behind, and says not to stand one in front of the stovepipe.
A magnetic stove fan clamps to the outside of a single-wall connecting fluepipe and pushes room air.
18 products checked · 54 hrs invested · +18,600 readers
Swipe for more
1-2 of 5
Personal buying guide
Question 1 of 2
What pipe are you clamping to?
The Drcokars HL-600A is a four-blade magnetic chimney fan listed at £31.99, with 4.4 from 1,735 reviews and a seller pipe band of 12–15.5 cm. In the first 50 UK texts the magnet comes up 20 times, and many buyers say it holds where the stove top is not flat and that the fan stays quiet. The stated range is 80–350°C, the noise attribute prints 32 decibels, and the bullets say no batteries or electricity. Other UK texts say the magnets are too weak for the weight, the supplied strap or belt is too short, and the fan has to sit very close to the firebox or it will not spin. The attribute weight is 900 g while a bullet prints 220 g, so neither figure is settled. One buyer says the page calls it magnetic but a jubilee clip is what actually holds it. It is the best value here if your pipe is inside 12–15.5 cm and you will use the returns window if the magnet slips.
Pros
Cons
Best for: A magnetic flue around 12–15.5 cm, when you want the lower amazon.co.uk price and a large UK review file.
Less suitable: Stainless pipe, a stove where the fan would foul the space above, or a gas appliance the listing does not clear.
Specifications
Common questions
What pipe size does Drcokars print?
The bullets say a chimney diameter of 12–15.5 cm, a circumference of 37.7–48.7 cm, and a height of 20–50 cm from the fireplace top.
Does this listing say it needs batteries?
No. The bullets say no batteries or electricity. The attribute power source is heat energy.
What do the saved UK reviews say about the magnet?
In the first 50 UK texts, the magnet is often called strong. Other texts say it slips and that a jubilee clip was used. The bullets name two magnets, not a clip.
The Signstek CF6-T is listed as a six-blade pipe fan at £31.44, with a triple-magnet base, a fixing ring, and a magnetic thermometer, and a stated range of about 80–345°C. The box lines are concrete: thermometer and fixing ring, a foldable handle in the bullets, 840 g, and 12.7 × 17 × 17 cm. The star line is 4.4 from 1,357, but in the first 50 saved UK texts almost none mention a magnet or a pipe, and many describe a fan sitting on a stove. That count is not evidence this pipe mount moves a measured volume of air, and no airflow figure is printed. Pipe diameter is not stated. A design attribute says table fan, which conflicts with the pipe-mount style. Use the hardware list, and treat the review total as a mixed pool.
Pros
Cons
Best for: You already know the pipe is magnetic and you want a thermometer and a fixing ring in the same box, while accepting thin evidence on this exact mount.
Less suitable: Anyone choosing from the 1,357 count, or a stainless, twin-wall, or gas flue the listing does not clear.
Specifications
Common questions
What comes in the Signstek box?
The listing includes a fixing ring and a magnetic thermometer with the fan. The bullets say it starts at about 80°C and give a range of 80–345°C.
How does the listing say to mount it?
On a magnet-compatible metal flue or chimney pipe, with a triple-magnet base and the supplied fixing ring. An airflow figure in cubic feet per minute is not stated.
Do the 1,357 reviews describe this pipe fan?
The star line is 4.4 from 1,357. In the first 50 saved UK texts, almost none mention a magnet or a pipe, and many describe a fan sitting on a stove. Do not treat that count as a pipe-fan sample.
The Valiant Remora FIR350 clamps to the flue rather than the stove top, and the amazon.co.uk file shows 4.4 from 446 reviews, with the first 50 saved texts from the United Kingdom. Buyers who are pleased describe a quiet spin once the pipe is warm, including on enamel, a boiler top, and stoves with no flat plate. The listing states a start as low as 50°C, with no batteries and no mains connection, and it names cool, irregular, soapstone, and angled tops. Several reviewers say the draught at the hand feels faint beside a fan that sits on the plate, and some report a slow start until the flue is very hot, with one text citing about 200 degrees. The title prints 200 mm while the attribute row prints 4.7 × 7.1 × 7.9 cm, so those two sizes cannot both describe the fan. Magnets fail on stainless pipe, and a few units stopped after days, about a month, about 14 months, or a couple of years. It is the top pick here because the saved UK texts actually describe a flue clamp, at £39.99, not because the breeze is strong.
Pros
Cons
Best for: You have a magnetic single-wall flue, a cool or awkward top, and you want the listing whose UK reviews describe that clamp.
Less suitable: Stainless or twin-wall pipe, a flat hot top where a stovetop fan is the simpler machine, or anyone who wants a strong blast of air.
Specifications
Common questions
Does the Valiant listing say it needs mains power?
No. The bullets say the fan is powered by heat from the stove, with no batteries and no mains connection. The stated start is as low as 50°C.
Which stove tops does this listing name?
Cool top, irregular surface, soapstone, or angled top. It uses a magnetic clamp on the flue pipe rather than sitting on the stove. The page question 'any stove' is not answered with a yes.
What size does the listing print?
The title says 200 mm. The technical row says 4.7 x 7.1 x 7.9 cm. Both figures are in the file, and they do not describe the same object. Pipe diameter is not stated in this saved listing.
The TITECK 8-blade lists at £31.34 with a retaining strap and a circumference of 15.45–24.72 inches, to sit about 8–20 inches above the stove. The bullets exclude gas stoves, pellet stoves, non-metallic pipe, and the stove top, and they say no drilling is required. The star line is 4.4 from 320, but of the first 50 saved texts only one is from the United Kingdom, and that text says the fan does not run. Most of the sample is from Germany, where some writers say it holds and stays quiet while others say the airflow feels slight. There is no start temperature in degrees Celsius, and material is not stated. The same country mix appears on the dual-head TITECK file, so this is not 320 independent UK opinions of an eight-blade pipe fan.
Pros
Cons
Best for: You have measured a magnetic metal flue inside 15.45–24.72 inches around and you accept a thin UK sample.
Less suitable: A buyer who wants UK reviews of this exact fan, or a gas or pellet stove.
Specifications
Common questions
Can this TITECK fan go on a gas or pellet stove?
The bullets say no. They also say it is not for a non-metallic chimney pipe and that it must not sit on the stove top.
What pipe size does the listing give?
A circumference of 15.45–24.72 inches, and a position about 8–20 inches above the stove. A millimetre diameter is not printed. The bullets say to measure before you buy.
How many of the saved reviews are from the UK?
The listing score is 4.4 from 320. In the first 50 saved texts, one is from the United Kingdom, and that text says the fan does not run. Most of the sample is from Germany.
The TITECK dual-head is listed at £37.99, at 990 g and 13 × 28.6 × 14.5 cm, with the same 15.45–24.72 inch circumference and the same exclusions as the 8-blade row. The seller says two heads help spread air across a wider area. A blade count per head is not stated, and there is no start temperature in degrees Celsius. The score is again 4.4 from 320, with the same first-50 mix and the same single UK sentence, which says the fan does not run. No saved UK text praises this dual-head model. At £6.65 more than the 8-blade listing, you pay for a wider body without a separate UK review file. It only makes sense if you have measured clearance for 28.6 cm of width and you accept that the stars are not evidence about two heads.
Pros
Cons
Best for: A wide magnetic flue run where one head would leave a dead side, after you have measured the 28.6 cm width.
Less suitable: Anyone treating 4.4 from 320 as proof this dual-head works, or a tight alcove with no room for the width.
Specifications
Common questions
How is the dual-head fan different in the listing?
The bullets describe two heads for a wider airflow, a width of 28.6 cm, and a weight of 990 g. The circumference band is the same 15.45–24.72 inches as the 8-blade TITECK listing. A blade count per head is not stated.
Where must it not be used?
The bullets say flue-pipe mounting only, not on the stove top, and not on gas stoves, pellet stoves, or non-metallic pipe. A retaining strap is included. Drilling is not required, on the seller's wording.
Is the 320-review line a separate UK sample?
The score is 4.4 from 320, the same figures as the 8-blade TITECK file. The first 50 texts show the same country mix and the same single UK sentence, which says the fan does not run.
Five amazon.co.uk listings, captured on 19 October 2026, were scored on a 0–100 scale. The star line is 25 points. All five listings print 4.4, so each scores 22. Usable review evidence is 30 points: a large count scores only when the saved texts describe a pipe fan. A mixed pool, or a file that is mostly not from the UK, scores low. Listing fit for a magnetic flue fan is 25 points, from pipe size, stated temperature, exclusions, a strap or ring, and conflicts in the spec rows. Price against that evidence is 20 points. A lower price scores more only when the review file is actually about a pipe fan. The highest score is the top pick. The highest price-against-evidence block is the best value. This is not a lab airflow test, and it does not invent a cubic-feet-per-minute figure.
Star line
25%Amazon rating divided by 5, then multiplied by 25. All five listings print 4.4, so each scores 22. The star line is the listing score, not a separate UK sample.
Usable review evidence
30%A large count scores only when the saved texts describe a pipe fan. A mixed pool, or a file that is mostly not from the UK, scores low. Maximum 30 points.
Listing fit
25%Pipe size, stated temperature, exclusions, a strap or ring, and conflicts in the spec rows. Maximum 25 points. A missing diameter or a clashing size row lowers the block.
Price against evidence
20%Shelf price in GBP against a review file that is actually about a pipe fan. A lower price scores more only in that case. Maximum 20 points.
Test the cold pipe with a fridge magnet, then match the seller’s size band, then read whether the reviews describe a pipe mount. A 4.4 star line is the listing score. It is not a UK verdict when the saved texts are German or describe a fan on the stove top. A magnetic stove fan does not replace a carbon monoxide alarm.
A magnetic stove fan is a pipe-clamped, heat-powered room-air fan. It sits on the outside of a single-wall connecting fluepipe and pushes room air. It does not plug in. It does not sit in the flue gas. A mechanical chimney fan that moves flue gas is draught equipment. The British Flue and Chimney Manufacturers Association says combustion products must still leave if that fan fails. A battery travel fan is not a stove fan.
All five listings print 4.4. Blade counts run from four to eight, and the dual-head row does not state a count per head. The score uses whether the saved texts describe a pipe fan, plus the stated fit and the price against that evidence.
Do not test a hot pipe by hand, slide a hot fan on enamel, or over-fire the stove to speed the blades. The top face of the module has to stay cooler than the base. Stopping the blades is how these modules die.
The Signstek 1,357 and the TITECK 320 are not a UK verdict on a pipe fan. In the saved texts, Signstek mostly describes a fan on a stove, and TITECK is mostly from Germany, with one UK sentence that says the fan does not run.
Do the magnet test cold. If a fridge magnet falls off, stop. Valiant states that stainless and double-wall pipe will not hold the Remora, and glossy vitreous enamel can be marginal even when it is steel. You need a hot single-wall pipe. Twin-wall stays cooler outside on purpose. Valiant’s guide puts the Remora 20–50 cm above the stove top, about 40 cm as the optimum, and asks for about 250 mm of pipe you can see. Measure against the seller’s band. Common UK connecting pipe is 125 mm or 150 mm.
A 4.4 average is not proof if the saved reviews are German, or if they describe a fan sitting on the stove top. The Valiant Remora has 4.4 from 446, and the first 50 saved texts are from the United Kingdom and describe a flue clamp. Drcokars has 4.4 from 1,735, and UK texts mention the magnet, including slip and clip complaints. Signstek has 4.4 from 1,357, but the first 50 saved UK texts mostly describe a fan on a stove, so that count is not scored as pipe-fan evidence.
Three typical situations, each with a recommendation from this comparison.
You have a magnetic single-wall flue and a cool, soapstone, angled or crowded top. The Valiant Remora FIR350 is the top pick at about £39.99: a flue clamp, a stated start as low as 50°C, and 4.4 from 446 reviews whose saved UK texts describe that clamp. The draught is often faint, and it will not hold on stainless pipe.
You have measured a magnetic flue around 12–15.5 cm and you want the lower amazon.co.uk price. The Drcokars HL-600A is the best value at about £31.99, with 4.4 from 1,735 reviews and UK texts that mention the magnet. Use the returns window if the magnet slips.
You already know the pipe is magnetic and you want a fixing ring and a magnetic thermometer in the same box. The Signstek CF6-T is about £31.44, with a stated range of about 80–345°C. The 4.4 from 1,357 is not a clean sample of this pipe mount, and pipe diameter is not stated.
The top pick is the Valiant Remora FIR350 at about £39.99. It clamps to the flue, the listing states a start as low as 50°C, and 446 amazon.co.uk reviews sit at 4.4, with saved UK texts that describe the clamp. Reviewers often call the draught faint, magnets fail on stainless pipe, and the title size of 200 mm conflicts with the attribute row. The best value is the Drcokars HL-600A at about £31.99: 4.4 from 1,735 reviews, a printed 12–15.5 cm pipe band, and UK texts that mention the magnet, if you use the returns window when the magnet slips. This is not a lab airflow test, and the fan does not replace a carbon monoxide alarm.
Drcokars HL-600A
Highest price-against-evidence block at about £31.99, with UK magnet comments and a printed 12–15.5 cm pipe band.
Editorial
Peter F. is the editor for DIY & tools at productscompared.co.uk. Comparisons in this category are checked against amazon.co.uk listings, review evidence and public UK sources.
Guides on what to look for, how to use a product, and common mistakes.
Public UK sources used for this comparison. amazon.co.uk prices, stars and review counts were taken from the listings on 19 October 2026.
This page contains affiliate links to amazon.co.uk (tag pcuk26-21). If you buy through them, we may earn a commission at no extra cost to you. Prices, stars and review counts are from the listings. This is not a laboratory test.
