The best wireless dimmers, compared.
Top pick: SIRYYUI strip dimmer Updated October 2026.
A wireless dimmer in a UK shop is not one object. It can be a smart wall module, a kinetic pad with a wired receiver, a 433 MHz mains remote, or a low-voltage controller for LED tape. A 230 V module dims a mains lamp. A strip controller sits after the driver, usually on 12 V or 24 V DC, and must not go across UK mains. Voltage, the lamp, a neutral and the protocol are set out in the [wireless dimmer buying guide](/hub/swimming-pools/wireless-dimmer/sub/wireless-dimmer-buying-guide). The card score is the star line times 20.
A wireless dimmer in a UK shop is not one object. It can be a smart wall module, a kinetic pad with a wired receiver, a 433 MHz mains remote, or a low-voltage controller for LED tape. A 230 V module dims a mains lamp.
32 products checked · 58 hrs invested · +21,400 readers
Swipe for more
1-2 of 9
Personal buying guide
Question 1 of 2
What are you dimming?
The SIRYYUI unit is an inline RF dimmer for a single-colour LED strip at about £9.99, and it belongs after the driver rather than on 230 V. The bullet says DC 5–24 V and 6 A, with printed caps of 30 W, 72 W and 144 W, while the table prints 5 V and 60 W. Fourteen amazon.co.uk reviews, all from the UK in the extract, give it 4.5 stars. Reviewers say it joins the strip with barrel connectors, and one notes that many tapes do not have that plug. The 14-button remote adds jump, fade and strobe, a memory of the last setting, and a 60-second switch-off, with a CR2025 cell in the box and a claimed range of 20 m. The listing marks it IP30 and says it is not water resistant. One review mentions power-supply whine. Fourteen reviews are too few for this 4.5 line to crown the category.
Pros
Cons
Best for: A single-colour cabinet or cove strip that already ends in a barrel connector.
Less suitable: A 230 V ceiling lamp, an RGB tape, or a damp room.
Specifications
Common questions
Can this dim a mains ceiling light?
No. The listing is a DC controller for a single-colour LED strip, 5–24 V in the bullet. The indoor line says it is not water resistant.
How does it connect to the strip?
UK reviews say it plugs in with barrel connectors between the driver and the strip. One review notes that many strips do not have that plug.
What do the buttons add beyond brightness?
The bullets list presets or 10–100% dimming, jump, fade and strobe, a memory of the last setting, and a 60-second switch-off.
The SONOFF Orb-DIM Matter is a mains wall module at about £25.63 that the table rates at 240 V and 400 W, or 2 A, for dimmable LED, incandescent and halogen. It holds 4.4 stars from 99 amazon.co.uk reviews, and UK reviewers name eWeLink, Alexa, Google Home, Apple Home, SmartThings and Home Assistant. The title requires a neutral, which many older UK switches do not have at the plate. Several UK reviews say the 86 mm body is a European plate and falls into a standard metal pattress. One reviewer used a 35 mm box, while another found the integrated body easier in a 25 mm box. SONOFF's help page caps dimmable LED at 200 VA and incandescent or halogen at 400 W, so the table's flat 400 W is wider than the LED figure. One review found Matter over Thread unreliable, one review records a dead-on-arrival unit, and the listed mark is IP20.
Pros
Cons
Best for: A ceiling lamp on a circuit that already has a neutral, in a deep box, if you want Matter or Wi-Fi.
Less suitable: A standard UK metal pattress, or a two-wire switch with no neutral at the plate.
Specifications
Common questions
Does this SONOFF dimmer need a neutral?
The title says a neutral is required. UK reviews in the capture say the same, and that many older UK switches have no neutral at the plate.
Will it fit a standard UK back box?
The table gives 8.6 × 8.6 × 3.4 cm. Several UK reviews say the plate is made for a European round box and falls into a standard metal pattress. One review used a 35 mm box. Another says the integrated body is easier in a 25 mm box.
Which apps do reviewers name?
UK reviews name eWeLink, Alexa, Google Home, Apple Home, SmartThings and Home Assistant. One review says Matter over Thread was unreliable. The listing itself names Matter, HomeKit, Alexa and Google Home.
The ECO-NEWLEAF kit pairs a battery-free kinetic pad, about 86 mm square, with a separate trailing-edge receiver on 240 V, at about £18.88. The bullet rates it at 4–100 W of dimmable LED or 200 W of incandescent or halogen, from 0–100%, on 433 MHz with no Wi-Fi and no app. It holds 4.4 stars from 24 amazon.co.uk reviews. The bullets do not mention a neutral, but UK reviews say the receiver needs one and that the listing did not make that clear. A bullet says IP65 for damp rooms, including a bathroom, the table says IP66, and one UK review says the pad is not waterproof and needs a box. One UK review says it did not dim, and another says dimming is slow to start. The maker's own FAQ says the pad cannot work alone and that dimming fails if the lamp is not compatible.
Pros
Cons
Best for: A second switch point without a new cable, if the lamp is marked dimmable and you can land a neutral on the receiver.
Less suitable: A bathroom bought on the IP line, or anyone who wants Alexa or Apple Home.
Specifications
Common questions
Does the kinetic receiver need a neutral?
The bullets do not say so. UK reviews say the receiver needs a neutral, and that the listing did not make that clear.
Is the pad waterproof?
A bullet says IP65 for damp rooms, including a bathroom. The table says IP66. One UK review says the pad is not waterproof and needs a box.
What can it dim?
The bullet says trailing edge, 4–100 W of dimmable LED or 200 W of incandescent or halogen, 0–100%. One UK review says it did not dim. Another says dimming is slow to start.
The Tedeligo three-module kit uses the same 433 MHz radio as the single module, sold as one remote and three dimmer modules at about £28.99, with five channels on the handset. The amazon.co.uk line is 4.3 from 60 reviews. The review text is mostly outside the UK, and the one UK review has no functional detail, so the stars are not British experience of the dimming. The pack bullet says three modules, while the number-of-items field says 1. Bullets print 10–150 W for LED and halogen on AC 220–250 V. The table prints 220 V, 10 A and 150 W, and the title also prints 50–200 VA. Each module is listed around 45 × 45 × 18 mm, the mark is IP00, and there is no Wi-Fi.
Pros
Cons
Best for: Three separate mains lamps on one 433 MHz handset, if you can live with the listing conflicts.
Less suitable: Anyone who wanted UK reviews of how it dims, or a remote that joins an app.
Specifications
Common questions
How many dimmers are in the box?
The pack bullet says one remote and three dimmer modules. The number-of-items field says 1.
Does the remote join Alexa?
The title says no Wi-Fi. The protocol is 433 MHz, with five channels on the handset. No smart-home app is named.
What load is printed?
Bullets say 10–150 W for LED and halogen, on AC 220–250 V. The table prints 220 V, 10 A and 150 W. The title also prints 50–200 VA.
The Tedeligo one-module kit is a 45 × 45 × 19 mm 433 MHz mains module plus a remote, at about £18.88, and it is the only kept listing with at least 100 amazon.co.uk reviews, at 4.2 from 239. The title says no Wi-Fi, so the handset does not appear in Alexa by itself. You dim from the remote and from the existing wall dimmer button. The bullets say AC 220–250 V and 10–150 W for LED and halogen, the table prints 110 V and 0.01 A, and the title adds 50–200 VA. The table says IP00, while a bullet claims 50 metres outdoors. UK texts in the first 50 reviews are few, one UK review says the module behaves as on and off with terminals too close for flex, and a neutral is not stated. That review count is why it is the top pick, not because the voltage lines agree.
Pros
Cons
Best for: An extra 433 MHz control for a mains lamp when you do not want an app.
Less suitable: Anyone who needs the table and the bullets to agree, or who wants the light in Alexa.
Specifications
Common questions
Does this Tedeligo kit use Wi-Fi?
The title says no Wi-Fi. The protocol line is proprietary 433 MHz. Control is the remote plus the existing wall dimmer button.
What load does the listing state?
The bullets say AC 220–250 V and 10–150 W for LED and halogen. The table also prints 110 V and 0.01 A. The title adds 50–200 VA. Those lines disagree.
Is it listed for outdoor use?
The specification table says IP00. A bullet claims 50 metres outdoors. The page asks about outdoor use and does not give a higher IP mark.
The BSEED listing in this set is the 86 mm white glass Zigbee touch dimmer at about £18.16, 40 mm deep and listed at 800 g. The title requires a neutral and a Zigbee 3.0 hub, sold separately, in a single-pole box. It shows 4.0 stars from 10 amazon.co.uk reviews. The only UK review in the notes is a faulty return, so the rest of that file should not be read as British opinion of it working. The title and the main bullets say Zigbee, while a later bullet calls it a Wi-Fi switch. The LED minimum is printed as 5 W, yet the table also prints 5 A, 250 V and 2,000 W. You slide the glass once the hub is there, and the warranty line is one year. No IP mark is given.
Pros
Cons
Best for: An 86 mm single-pole box that already has a neutral, if you own a Zigbee hub and will test the plate on arrival.
Less suitable: Anyone who needed UK reviews of it working, or a two-wire switch with no neutral.
Specifications
Common questions
What has to be in the wall already?
The title says a neutral is required. The bullet says a Zigbee 3.0 hub, sold separately, and a single-pole box. This ASIN is the 86 mm white plate.
Is it Wi-Fi or Zigbee?
The title, the protocol field and the main bullets say Zigbee. A later bullet calls it a Wi-Fi switch. Both lines are in the same listing.
What is the minimum LED load?
The bullet says dimmable LED, halogen and incandescent, with a 5 W minimum for LED. The table prints 5 A, 250 V and 2,000 W.
The Taoellen unit is a touch-panel dimmer for a single-colour LED strip or module on DC 5–24 V, at about £18.99, with 30 A and 720 W printed in the table. The page says single colour only, so it is not an RGB controller. Two amazon.co.uk reviews give it 4.0 stars. The bullet lists a 1-hour and a 2-hour delay-off, a night-light mode, and settings kept after power is lost, from the panel and a rotary ring. Mounting is the weak point. The bullet says adhesive tape or screws, and one of the two UK reviews says the panel only sticks to the breakout box and has no screws. The warranty field reads NO, and no IP mark is listed. Two reviews cannot carry a 30 A claim, so that current stays a printed number.
Pros
Cons
Best for: A single-colour cove or cabinet run, if you will check the fixings when the parcel arrives.
Less suitable: RGB tape, a 230 V lamp, or a buy that depends on the 30 A line being proved.
Specifications
Common questions
Will this run an RGB strip?
The page asks that. The bullets and the title say single colour only: LED strips, COB strips and LED modules on DC 5–24 V.
Can the panel be screwed to the wall?
The bullet says adhesive tape or screws. One of the two UK reviews says the panel only sticks to the breakout box and has no screws.
Does it switch itself off later?
The bullet lists a 1-hour and a 2-hour delay-off, a night-light mode, and settings kept after power is lost.
The SONOFF Orb-ZBDIM is the Zigbee plate at the same about £25.63, and the table states 220 V and 1 A with no wattage line. It sits at 3.5 stars from 92 amazon.co.uk reviews, the lowest star line among the mains plates in this set. UK reviewers pair it with Zigbee2MQTT and Home Assistant. The listing calls the unit a Zigbee repeater, not a hub, so you still need a coordinator, and the title requires a neutral. UK reviews say the round European plate does not sit flush on an 86 mm box, the plate falls in, and the supplied screws do not match. One reviewer doubted a 25 mm box and used 35 mm. Pairing is a press-and-hold on a button on the back, which means taking the cover off. One review records a dead-on-arrival return, and the listed mark is IP00.
Pros
Cons
Best for: A Zigbee coordinator you already run, plus a neutral in a deep box.
Less suitable: A standard UK metal pattress, a two-wire switch, or a first smart plate when you wanted a higher star line.
Specifications
Common questions
Does the Zigbee Orb need a hub?
The protocol line is Zigbee, and the title says a neutral is required. UK reviews pair it with Zigbee2MQTT and Home Assistant. The listing calls the unit a Zigbee repeater, not a hub.
Will the plate fit a UK square box?
UK reviews say it is a round European plate. It does not sit flush on an 86 mm box, the plate falls in, and the supplied screws do not match. One review doubts a 25 mm box and used 35 mm.
Where is the pairing button?
One UK review says you pair it by pressing and holding a button on the back, which means taking the cover off.
The NiuLumea listing is an ABS RF box at about £8.47, about 10.5 × 10.8 × 2.8 cm and 180 g, and the file has no amazon.co.uk review line. The bullets put it on DC 12–24 V, up to 18 A and 432 W at 24 V, with a seller claim of 30 metres including through walls. The title says dimmer, while the bullets describe an RGB controller with colour, gradients, flashing and breathing. A touch panel is mentioned, but there is no included-components line and no IP mark. The comparison score is 0 because the review count is missing, so the price is the only buyer signal on the page. Treat the 18 A and 30 m figures as print from the seller, not as a measured result.
Pros
Cons
Best for: A buyer who already wants an RGB controller and will check the box against the bullets on arrival.
Less suitable: Anyone who wants a reviewed single-colour dimmer, or a switch for a mains lamp.
Specifications
Common questions
Is this a mains dimmer?
The file does not show a mains voltage. The bullets say DC 12–24 V, up to 18 A, and up to 432 W at 24 V.
Does it only dim, or does it change colour?
The title says dimmer. The bullets describe an RGB controller with colour, gradients, flashing and breathing. There is no review line to compare.
How far does the remote claim to work?
The bullet says 30 metres, including through walls. That figure is the seller's claim.
Shelf prices, stars and review counts are the amazon.co.uk figures stored for these nine listings on 16 October 2026. There was no bench dimming trial and no laboratory score. The number on each card is the star line times 20. A file with no review line scores 0. The top pick is a separate rule: the highest star line among listings with at least 100 reviews. Listing clashes, the lamp and the price are written beside that number. They do not change it.
Voltage and lamp
30%A 230 V module is for a mains lamp. A strip controller has to match the driver, usually 12 V or 24 V DC, and the bulb or tape has to be dimmable.
Neutral, hub and protocol
25%Whether the listing states a neutral, a Zigbee coordinator, or no app at all. A 433 MHz handset does not join Alexa by itself.
Plate, box and listing clarity
20%A UK square box versus a European round plate, and whether the table and the bullets print the same voltage, load and IP mark.
Review evidence
15%The amazon.co.uk star line and how many reviews sit behind it. The top pick needs at least 100 reviews. A missing review line scores 0.
Price in this set
10%The captured shelf price, from about £8.47 to about £28.99. A higher price in this scrape is not a quality signal.
A wireless dimmer on this page is a smart wall module, a kinetic pad with a wired receiver, a 433 MHz mains remote, or a low-voltage controller for LED tape. The nine amazon.co.uk listings run from about £8.47 to about £28.99. Use voltage, the lamp, a neutral and the plate before the price.
A wireless dimmer in this comparison is one of four things: a smart wall module, a kinetic pad with a wired receiver, a 433 MHz mains remote, or a low-voltage controller for LED tape. You separate them by voltage class first. UK mains are about 230 V. A mains module dims a lamp on that supply. A strip controller has to match the driver output, usually 12 V or 24 V DC, and must never be connected across UK mains.
Three on/off kinetic or radio switches were set aside from this set. A handset that only switches does not dim. Read the load line for a wattage band, not only the word wireless.
UK reviews of both SONOFF Orb plates say the body is a European plate and can fall into a standard metal pattress. The supplied screws on the Zigbee Orb are also reported as a poor match. An 86 mm title is not proof that the plate sits flush.
A strip controller belongs on the driver output, usually 12 V or 24 V DC. It must not go across UK mains. Dimming a bulb that is not marked dimmable, or expecting a 433 MHz handset to appear in Alexa, fails for the same reason: the listing and the lamp are different jobs.
Start with voltage. UK mains are about 230 V. The Tedeligo bullets say 220–250 V, while the one-module table also prints 110 V. The SONOFF Matter table says 240 V. The Zigbee Orb table says 220 V. The BSEED table says 250 V. The strip controllers are DC: SIRYYUI 5–24 V in the bullet, Taoellen 5–24 V, NiuLumea 12–24 V. A controller on the wrong side of the driver is the wrong product. Then the lamp. The packet has to say dimmable.
The plate has to fit the box you have. UK reviews of both SONOFF Orb modules say a European body falls into a standard metal pattress. One Matter review used a 35 mm box. One Zigbee review doubted 25 mm and used 35 mm, and said the screws do not match. BSEED is an 86 mm glass plate, 40 mm deep, which is the UK square size, on only 10 reviews, and the only UK review in the notes is a faulty return. IP marks are seller print until they agree.
Three typical situations, each with a recommendation from this comparison.
You want to dim a mains lamp from another point, and you do not want Wi-Fi. The Tedeligo one-module kit is about £18.88, with 4.2 from 239 reviews, on 433 MHz. The bullets say 220–250 V and 10–150 W. The table also prints 110 V and 0.01 A, and the mark is IP00.
You already use a smart home, and the box has a neutral. The SONOFF Orb-DIM Matter is about £25.63, with 4.4 from 99 reviews, Matter and Wi-Fi, and 240 V and 400 W in the table. UK reviews say the plate falls into a standard metal pattress. The help-page LED limit recorded for this card is 200 VA.
The lamp is tape after a driver, not a 230 V ceiling light. The SIRYYUI strip dimmer is about £9.99, with 4.5 from 14 reviews and a DC 5–24 V bullet. It uses barrel connectors. The listing says IP30 and not water resistant. Fourteen reviews are a small sample.
The top pick is SONOFF Orb-DIM Matter, with the highest score in this comparison (8.7 out of 10, from 99 amazon.co.uk reviews). No listing has both 4.3 stars and at least 100 reviews, so this page does not name a best value. The SIRYYUI strip dimmer is 4.5 from 14 reviews at about £9.99, which is too small a sample to carry that award. None of these scores is a lab test.
No award. The rule needs 4.3 or above and at least 100 reviews. No kept listing meets both.
Editorial
Peter F. is the editor for DIY & tools at productscompared.co.uk. Comparisons in this category are checked against amazon.co.uk listings, review evidence and public UK sources.
Guides on what to look for, how to use a product, and common mistakes.
Public UK sources for electrical work, bathroom zones and connectable-product security. Listings are the amazon.co.uk captures for these nine ASINs on 16 October 2026, not a live reload. Prices on amazon.co.uk move.
This page contains affiliate links to amazon.co.uk. If you buy through them, we may earn a commission at no extra cost to you. Prices, stars and review counts come from those listings. We did not run a laboratory test. The scores rank a listing inside this set only.
