The best cordless nailers, compared.
Top pick: VeftBltrem 21 V 2-in-1 cordless nailer Best value: SEESII 18V 2-in-1 cordless nailer and stapler – Two batteries, a charger, a bag and fasteners at about £99.99, with 4.2 from 210 reviews. The brad length stops near 32 mm. Updated October 2026.
A cordless nailer drives collated brads, and often narrow-crown staples, without a compressor, a hose or a gas fuel cell. You are usually fitting bead, panelling, cabinet backs, fence slats or upholstery, and skirting only when the nail is long enough to reach timber. A higher gauge is a thinner nail, and a 16-gauge finish nail will not fit an 18-gauge magazine. The twelve amazon.co.uk listings cluster as a 4 V craft tacker, 2-in-1 guns that stop near 32 mm, and two body-only 18 V guns that state a 50 mm maximum. The [cordless nailer buying guide](/hub/staplers-and-nail-guns/cordless-nailer/sub/cordless-nailer-buying-guide) takes gauge, length and kit versus body before the table.
A cordless nailer drives collated brads, and often narrow-crown staples, without a compressor, a hose or a gas fuel cell.
42 products checked · 58 hrs invested · +24,600 readers
Swipe for more
1-2 of 12
Personal buying guide
Question 1 of 2
How long a brad do you need?
The VeftBltrem kit combines 18-gauge brads and quarter-inch crown staples with single and contact firing. Two batteries, a charger and 1,000 of each fastener are advertised for £76.99, making the package look unusually inexpensive. A rotary depth knob gives some control over finish, and the listing claims 1,500–2,000 shots per charge. The apparent 5.0-star score is based on only three reviews, however, so it is not strong evidence of reliability or consistent driving performance. Battery capacity is not stated, the voltage wording contains an error, and the included-components line does not clearly confirm a case. This is a budget gamble for light work, not a defensible category winner despite the perfect displayed rating.
Pros
Cons
Best for: Low-cost light trim or upholstery when you accept limited evidence
Less suitable: Reliability-critical jobs, long skirting fixings or buyers who want proven specifications
Specifications
Common questions
What fasteners does the listing state?
18-gauge brads from 5/8 inch to 1-1/4 inch, and 1/4 inch crown staples from 5/8 inch to 1 inch, plus 1000 of each in the title.
Are two batteries included?
The bullets say two batteries and a charger are equipped. Amp-hours are not stated.
How many reviews are on the listing?
The listing line says 5.0 from 3 reviews.
This NEU MASTER kit supplies an 18 V 2.0 Ah battery and charger, so it can be used without buying into a separate platform. The listing claims up to 2,000 nails per charge and includes an LED and belt hook, features that suit mobile snagging and trim work. Its 4.9-star rating looks impressive, but it is based on only 14 reviews and should not outweigh better-established listings. More importantly, the product bullets do not state a supported nail-length range, so a buyer cannot confirm from the specification whether it suits a particular skirting or moulding job. No nails or staples are included, and a case is not named in the box contents. It is therefore a plausible light-duty kit, but too many practical purchasing details remain unspecified for it to be a top pick.
Pros
Cons
Best for: Light DIY trim when you can verify the required fastener size before ordering
Less suitable: Jobs with a fixed nail-length requirement or buyers wanting a fully documented starter kit
Specifications
Common questions
Are nails included?
No. The listing says nails and staples are not included.
What battery is in the box?
One 18 V 2.0 Ah battery and a 2.4 A charger.
Does the listing state a nail length range?
Not in the product bullets. A review mention of 10–32 mm is not a specification line.
The NEU MASTER 2-in-1 fires 15–32 mm 18-gauge brads and 15–25 mm narrow-crown staples, a useful range for trim, woodworking and upholstery. The £109.99 package includes a 2.0 Ah battery, charger, 800 nails and 200 staples, so there is little else to buy for the first job. A contact safety requires the nose to be pressed against the work before firing. The 4.6-star rating is encouraging, but only 16 reviews sit behind it, which makes recurring faults and long-term durability hard to judge. The listing does not clearly state depth adjustment, jam release, case or even battery voltage, despite naming battery capacity. Its 32 mm ceiling also keeps it in the light finishing class rather than making it a general answer for skirting or structural timber.
Pros
Cons
Best for: Thin trim, craft, furniture backs and upholstery
Less suitable: Thick skirting, structural timber or buyers who need well-documented controls
Specifications
Common questions
What does the box include?
The nailer, 800 nails, 200 staples, a 2.0 Ah battery and a 2.4 A charger.
What sizes does the listing state?
18-gauge brads from 15 mm to 32 mm, and 5.7 mm narrow-crown staples from 15 mm to 25 mm.
Is it described as suitable for structural timber?
A review says it is for lighter jobs, not thick structural timber. The bullets name thin trim, woodworking and upholstery.
The Einhell TE-CN 18 Li is a compact 2-in-1 tool for brads and staples, supplied with 300 of each fastener. Its variable depth setting, firing lock, magazine indicator and belt clip make it well equipped for light trim and upholstery. The 4.5-star rating is backed by 3,607 reviews, the largest evidence base in this category. At £63.14 it is excellent value only if an 18 V Power X-Change battery and charger are already on your shelf, because neither is included. The supplied nails are 32 mm and the listing does not establish a longer brad capacity, so it sits below the length commonly chosen for skirting into studs. Existing Einhell owners get a credible best-value option for lighter work; everyone else should compare the cost of a battery kit before treating the body price as the final price.
Pros
Cons
Best for: Power X-Change owners doing light trim, upholstery and craft work
Less suitable: Buyers starting a new battery platform or fitting skirting that needs longer brads
Specifications
Common questions
Is a battery included?
No. This is the TE-CN 18 Li body. It needs one 18 V Power X-Change battery and a charger, sold separately.
What fasteners are in the box?
300 nails of 32 mm and 300 staples of 19 mm. A highlight line also says 22 mm staples.
What firing rate does the listing claim?
20 shots per minute.
The Einhell FIXETTO 18/50 N takes 15–50 mm 18-gauge brads, giving it enough stated length for jobs that the many 32 mm kits cannot cover. It offers depth adjustment, single or series firing and a 100-nail magazine, with a listing claim of up to 60 impacts per minute. The 4.5-star rating is backed by 1,034 reviews, combining useful review volume with a clearly documented specification. At £147.99 it is a bare tool, so its value is strongest if you already own an Einhell Power X-Change battery and charger. The listed 3.1 kg weight is substantial, and no case is included. For an existing Power X-Change owner who needs up to 50 mm brads, it is the top pick here; starting from no battery makes a complete kit or a different platform comparison more sensible.
Pros
Cons
Best for: Power X-Change owners fitting substantial trim or skirting into suitable timber backing
Less suitable: First-time platform buyers, staple work or prolonged overhead use
Specifications
Common questions
Is a battery included?
No. The FIXETTO 18/50 N is supplied without a Power X-Change battery or charger.
What nail size does the listing state?
18-gauge nails, 1.0 mm wide, from 15 mm to 50 mm. 500 nails of 50 mm are included.
Can it fire more than one nail in a run?
The listing has a shot regulator for single shot or series shot, and claims up to 60 impacts per minute.
The Ryobi R18GN18-0 fires 15–50 mm 18-gauge brads, placing it among the few tools here with a stated range suitable for longer second-fix work. Tool-free depth adjustment and jam release reduce interruptions, while the Grip-Light LED and reversible belt hook help when moving through rooms. Its 4.5-star rating comes from 546 reviews, enough to carry more weight than unusually high ratings from very small samples. The £159.63 listing is a bare tool with no battery, charger, nails or confirmed case, so the real starting cost depends on whether you already use Ryobi ONE+. At 2.4 kg it is lighter than the listed FIXETTO weight, although still heavier in the hand than a pneumatic brad nailer. It is a strong top-pick alternative for ONE+ owners, but a poor-value entry point if you must buy the battery system solely for this job.
Pros
Cons
Best for: Ryobi ONE+ owners doing skirting, architrave and other longer-brad second-fix work
Less suitable: Buyers without ONE+ batteries or anyone needing a 2-in-1 stapler
Specifications
Common questions
Does it include a battery?
No. The listing is the R18GN18-0 bare tool. Battery and charger are excluded.
What nails does the listing state?
18-gauge nails, 1.2 mm, from 15 mm to 50 mm.
Is jam clearing tool-free?
Yes. The bullets state tool-free depth of drive and a tool-free jam release.
The LINKNAL L820-BN is a complete 18-gauge brad-nailer kit with two batteries, a charger, 1,000 nails and a toolbox. Sequential and contact modes cover careful placement and faster repetitive work, while the contact trip and dry-fire lockout add useful safeguards. Its 4.5-star rating is based on 504 reviews, giving the model a credible body of buyer feedback. The main purchasing problem is that the listing states the gauge but not the supported nail-length range, so you cannot confirm whether it will take the length required for skirting or thicker trim. The quoted 5.4 kg is a package figure rather than a clear tool-only weight, and staples are not supported. It is attractive as a ready-to-use brad kit, provided the seller confirms the required nail length before you buy.
Pros
Cons
Best for: General brad work when you want a complete kit and can confirm fastener length
Less suitable: Length-critical skirting jobs or upholstery that requires staples
Specifications
Common questions
What is in the box?
Two 20 V MAX batteries, a charger, 1000 18-gauge nails, the nailer and a toolbox. Amp-hours are not stated.
Does the listing state nail length?
No. Gauge is 18. Length is not stated, so confirm it with the seller before a length-critical job.
What safety features does the listing name?
The contact trip must be fully depressed. Sequential and contact modes are named, and a dry-fire lockout is stated.
The BLUEMARS is an 800 g, 4 V cordless tacker for type 53 staples and short type 47 nails, not an 18-gauge second-fix gun. Its built-in 1.5 Ah battery charges by USB-C, which is convenient for craft and occasional upholstery work, and the listing claims up to 30 shots per minute. At £29.99 it is the cheapest tool here, but that price reflects a different class of machine rather than an exceptional deal on a brad nailer. The 14–15 mm type 47 nails are far too short for jobs such as fixing skirting through plasterboard into timber. Its 4.4-star rating comes from 37 reviews, and the listing conflicts over how many nails and staples are supplied. Choose it for card, fabric and thin materials, not because a search result has placed it beside full-size 18-gauge tools.
Pros
Cons
Best for: Craft, fabric, light upholstery and thin-sheet fastening
Less suitable: Skirting, architrave, hardwood trim or any job requiring 18-gauge brads
Specifications
Common questions
Is this an 18-gauge brad nailer?
No. The listing states type 47 nails of 14–15 mm and type 53 staples of 6–14 mm, on a 4 V battery.
How is it charged?
A USB-C cable is included, with a 1.5 Ah battery. A mains charger brick is not named.
What weight does the listing state?
800 g.
The established NEU MASTER NTC0023-18 covers 15–32 mm brads and 15–25 mm staples, enough for beading, panelling and many upholstery jobs. A battery and charger are included, and the listing claims up to 1,100 full-power shots per charge rather than leaving you to source a compatible pack. The 4.2-star score comes from 1,894 reviews, giving it one of the strongest bodies of buyer feedback in this comparison. Its 2 kg listed weight is manageable for short runs, and the LED and belt hook are practical additions. However, the listing alternates between 18 V and 20 V Max wording, and the exact starter-fastener assortment is not clear in the included-components line. The 32 mm maximum also means you should not assume it can make a secure skirting fixing through board and plaster into timber.
Pros
Cons
Best for: General light finishing and upholstery where 32 mm brads are sufficient
Less suitable: Long-brad skirting work or buyers who need an unambiguous box inventory
Specifications
Common questions
What is the longest fastener the listing states?
Maximum nail length 32 mm and maximum staple length 25 mm. Brads are 18-gauge from 15 mm to 32 mm.
How many shots does the listing claim per charge?
Up to 1100 full-power shots from the 2.0 Ah pack. That is a listing claim, not a measured test.
Is a battery included?
Yes. Included components name a battery pack and a charger.
The SEESII drives 18-gauge brads up to about 32 mm and narrow-crown staples up to about 25 mm, making it a practical kit for mouldings, light trim and upholstery. Both sequential and contact firing are available, while the six-stage depth dial and tool-free jam release give you useful control without reaching for another tool. Two 2.0 Ah batteries, a charger, a bag and starter fasteners are included, so the £99.99 price is directly comparable with a complete kit rather than a bare tool. Its 4.2-star rating is supported by 210 reviews, which is a more useful signal than a near-perfect score from only a handful of buyers. The limitation is the roughly 32 mm maximum brad: it falls short of the 38–50 mm often chosen when fixing skirting into studs. At 3.51 kg as listed, it is also one of the heavier options here, and harder timber may expose the difference between this DIY kit and a longer, more powerful second-fix nailer.
Pros
Cons
Best for: Light trim, beading, cabinet backs and upholstery when you want a complete kit without joining a battery platform
Less suitable: Skirting that needs 38–50 mm fixings, hardwood production work or structural timber
Specifications
Common questions
Does the listing include batteries and a case?
The listing includes two 2000 mAh batteries, a charger, a bag, and 1000 nails and staples.
What fasteners does the listing state?
18-gauge brad nails from 5/8 inch to 1-1/4 inch, and 1/4 inch crown staples from 5/8 inch to 1 inch.
Which fire modes does the listing name?
Sequential single fire and contact bump fire, plus a contact safety tip and a tool-free jam release.
The Tacwise Master Nailer 191 fires 15–32 mm 18-gauge brads and 15–25 mm type 91 staples, with sequential single-shot operation. Its £86.62 kit includes a battery, charger, carry case, 2,000 brads and 1,000 staples, making the first-job cost easy to understand. A depth adjuster and 100-fastener metal magazine suit repeated light finishing work, and the listing claims around 1,000 shots per charge. The 4.2-star rating comes from 91 reviews, a reasonable but not extensive evidence base. There is no bump mode, which reduces speed but gives deliberate control for occasional DIY use. The larger limitation is the 32 mm maximum brad, so this kit is well stocked for upholstery and thin trim but short of the lengths commonly chosen for skirting into studs.
Pros
Cons
Best for: Upholstery, panelling, thin trim and occasional DIY with a complete kit
Less suitable: Fast production runs or skirting that requires 38–50 mm fixings
Specifications
Common questions
Which fasteners does the listing state?
Type 91 staples from 15 mm to 25 mm, and 18-gauge brads from 15 mm to 32 mm. The box includes 1000 staples of 25 mm and 2000 nails of 32 mm.
Is bump fire included?
No. The listing states sequential single-shot firing.
Is a battery included?
Yes. A 20 V battery and charger are included. Amp-hours are not stated.
The Yofuly handles 15–32 mm 18-gauge brads and 15–25 mm staples, covering light trim, craft and upholstery jobs. Its kit is generous on paper: two 4.0 Ah batteries, a charger, 1,000 nails and 1,000 staples are included for £84.69. A depth knob and integrated LED are useful when you are working along an awkward edge, and the contact tip requires deliberate pressure before firing. Confidence is lower than the box contents suggest because the 4.0-star rating comes from only 34 reviews. The listing also conflicts on weight and gives implausible dimensions, while its Makita-compatibility wording is not enough to treat battery fit as proven. As with most 32 mm kits, it is better suited to light finishing than to skirting where the fixing must pass through plasterboard and reach a stud.
Pros
Cons
Best for: Occasional light trim, upholstery and workshop jobs where a complete 2-in-1 kit matters
Less suitable: Buyers relying on verified Makita battery compatibility or needing 38–50 mm brads
Specifications
Common questions
What nail and staple sizes does the listing state?
18-gauge brad nails from 15 mm to 32 mm, and 18-gauge staples from 15 mm to 25 mm.
Are batteries included?
Yes. The listing includes two 4000 mAh batteries and a charger.
Does the listing state a safety nose?
Yes. It says the tool fires only when the trigger and the safety contact tip are both pressed.
For this comparison we scored twelve amazon.co.uk cordless-nailer listings dated 15 October 2026. Scores run from 0 to 100. They are editorial comparison scores, not laboratory results, and they do not replace the star rating shown beside each product. Shot-count and firing-rate lines are listing claims.
Amazon rating and review confidence
40%The displayed star rating is moderated by review count, so three or 14 reviews cannot outweigh a similar score supported by hundreds or thousands.
Fastener capability and control
25%Stated nail range, staple support where relevant, depth adjustment, firing modes, jam access and safety features are considered. An unstated nail range is a material gap.
Package and platform value
20%Battery, charger, case and fasteners are assessed against the listed GBP price. A bare tool receives full value only for a buyer who already owns the platform.
Listing clarity
10%Conflicting dimensions, voltage, weight or included-item claims reduce the score.
Handling and support
5%Listed weight, warranty information, magazine features, LEDs and belt hooks contribute where the listing supports them.
Start with the length the timber actually needs, then the gauge, then whether the battery is in the box. A cordless nailer here is a battery brad gun, often a 2-in-1 that also takes short narrow-crown staples. It is not a framing nailer and not a compressor gun. On 15 October 2026 the twelve amazon.co.uk prices ran from about £29.99 to about £159.63. A 32 mm maximum sits outside the 38–50 mm skirting band those sellers describe.
A cordless nailer is a battery tool that drives collated brads, and often narrow-crown staples, without a compressor, a hose or a gas fuel cell. People buy one for second-fix and light making: bead, panelling, cabinet backs, fence slats, upholstery, and skirting only when the nail is long enough to reach timber. An 18-gauge brad is about 1.2 mm. A higher gauge is a thinner nail. A 16-gauge finish nail will not fit an 18-gauge magazine.
The Ryobi at about £159.63, the FIXETTO at about £147.99 and the TE-CN at about £63.14 leave out the battery and charger. Add that cost before you compare them with a SEESII or Tacwise kit. ONE+ packs do not fit Power X-Change.
Most 2-in-1s in this set stop near 32 mm. That is outside the 38–50 mm band described for typical skirting into studs. The listing’s maximum is the limit, not a starting point you can stretch.
A 16-gauge finish nail will not fit an 18-gauge magazine. Angled 16-gauge nails are the wrong collation. Brick, block and dot-and-dab plasterboard are not a brad job. A short craft nail from the 4 V tacker is a different tool again.
Softwood trim and fence battens are in scope for an 18-gauge brad. Brick, block and dot-and-dab plasterboard are not. Length is the next cut. Tradefix recommends 50 mm 16-gauge second-fix nails through skirting and plasterboard into studs, plus adhesive. Always First 4 Fixings says 38–50 mm 18-gauge brads are often used on typical 12–18 mm skirting. A gun that stops at 32 mm cannot follow that length.
Three listings are body only: Ryobi B09VTG4T6W at about £159.63, Einhell FIXETTO at about £147.99, and Einhell TE-CN at about £63.14. A bare tool is good value only when you already own that platform. ONE+ packs do not fit Power X-Change. Kits such as the SEESII, with two 2.0 Ah batteries, a charger, a bag and fasteners at about £99.99, put the first-job cost on the shelf price. Where amp-hours are missing, as on the Tacwise and the LINKNAL, treat runtime claims as unstated.
Three typical situations, each with a recommendation from this comparison.
You are fitting pine bead or a short run of fence slats, and you want a battery in the box. Sequential fire is the lower-risk default. The Tacwise Master Nailer 191 states sequential single-shot only, with a 20 V battery, charger, case, 15–32 mm brads and type 91 staples, at about £86.62.
You already own Einhell Power X-Change, and the job needs a stated 15–50 mm 18-gauge brad. The FIXETTO 18/50 N is the body-only top pick in this set, at about £147.99, with 4.5 from 1,034 reviews. The battery and charger are sold separately.
You do not own a platform, and about 32 mm is enough for mouldings, cabinet backs and upholstery. The SEESII kit includes two 2.0 Ah batteries, a charger, a bag and starter fasteners at about £99.99, with 4.2 from 210 reviews. It is the wrong shelf when skirting needs 38–50 mm.
The top pick is the Einhell FIXETTO 18/50 N for its stated 15–50 mm capacity, depth adjustment, single or series firing, and 4.5 from 1,034 reviews, particularly if you already own Power X-Change. At about £147.99 it is body only. The best value is the SEESII kit at about £99.99: two batteries, a charger, a bag and fasteners, with 4.2 from 210 reviews. Its roughly 32 mm maximum brad is a clear limit for skirting into studs. A 5.0 from three reviews does not outrank a longer, better documented gun. A 32 mm kit is the wrong shelf for a trade second-fix carpenter who needs 50 mm, or 16-gauge, all day.
SEESII 18V 2-in-1 cordless nailer and stapler
Two batteries, a charger, a bag and fasteners at about £99.99, with 4.2 from 210 reviews. The brad length stops near 32 mm.
Editorial
Peter F. is the editor for DIY & tools at productscompared.co.uk. Comparisons in this category are checked against amazon.co.uk listings, review evidence and public UK sources.
Guides on what to look for, how to use a product, and common mistakes.
Public UK sources and amazon.co.uk listings checked on 15 October 2026. Prices move. No laboratory test.
This page contains affiliate links to amazon.co.uk. If you buy through them, we may earn a commission at no extra cost to you. Scores compare published listings and review counts. They are not a laboratory test.
