Independent comparisons. We may earn from shop links. More info

90 vs 105 degree drill attachment

Updated: 2026-10-23

You can already see the gap: a hinge screw against a cabinet stile, a bracket under a drawer, or a fixing beside a joist. The choice is the angle, not a brand league. A square 90-degree head keeps the bit at right angles and the tool close to the face. A 105-degree head tips the body off that face so your hand clears. They lose in different cupboards. Prices stay on the [right angle drill attachment comparison](/hub/drilling-and-accessories/right-angle-drill-attachment). Products Compared read listing bullets and maker pages, not a survey of kitchens, on 22 October 2026. A qualifying purchase can earn a commission at no extra cost to you.

You can already see the gap: a hinge screw against a cabinet stile, a bracket under a drawer, or a fixing beside a joist. The choice is the angle, not a brand league.

Our top picks

Milwaukee Milwaukee 4932471274

Best overall

Milwaukee Milwaukee 4932471274
9.2/10about £14.95
View offer
DeWalt DeWalt DT20500-QZ

Alternative

DeWalt DeWalt DT20500-QZ
8.7/10about £23.95
View offer
ColumPRO ColumPRO 105 degree

Best value

ColumPRO ColumPRO 105 degree
7.9/10about £6.99
View offer
On this page
  1. 1.What the two angles do
  2. 2.The 90-degree heads you can measure
  3. 3.The 105-degree heads in this set
  4. 4.Cabinets, decks and the gap that still fails
  5. 5.A choice with a condition

What the two angles do

Ninety degrees means the bit leaves the head square to the shank, and the drill sits parallel to the panel. That suits a shallow return, a toe space, or the gap between a carcass and a wall. If the head is 36 mm or about 38 mm front to back and your clearance is less than that, the square head still will not enter. A hundred and five degrees adds about 15 degrees of tilt, so the body clears a stile, a battery and a second hand. The bit is no longer square to the drill body. The two shapes are not interchangeable. Hold a bit on the screw and see whether the obstruction is in front of the screw or beside the drill. If both directions are blocked, neither angle fits. The order of those questions is the buying guide.

The 90-degree heads you can measure

Milwaukee’s 4932471274 states a true 90 degrees and 36 mm, at £14.95 with 4.8 from 5,281 ratings, plus ten bits. It is a 1/4 inch hex output. The DT20500 is stated at 38 mm and 43 Nm, at £23.95. The DWARA120 states 1.5 inches front to back, at £24.99 with 4.7 from 21,560 ratings. Both DeWalt heads say impact-ready, and 43 Nm belongs only to the DT20500. DODUOS and HSEAMALL are 90-degree chucks, impact not stated. The DWARAFS is a 12 inch shaft for a bend, not a shallow head. One UK review limits it to driving, not drilling.
Milwaukee Milwaukee 4932471274

Testsieger

Milwaukee Milwaukee 4932471274
9.2/10about £14.95
View offer

The 105-degree heads in this set

None of the 105-degree listings publish a head depth next to 36 mm. The ColumPRO OB05-205 is £6.99 with 4.0 from 360 ratings: 105 degrees, 1/4 inch hex and 10 Nm, for a drill. It is the best value when the body needs to tilt, and reviews say you grip the housing or it spins. It is not a 43 Nm impact head. The S003-105 at £11.99 adds 50 mm and 25 mm bits, and the impact line describes the bits. The Motrijuka pair is £4.99 from 15 ratings, shank unstated. The QHSXMQ kit includes both angles, and reviewers say the 90-degree piece is hand-only.

Cabinets, decks and the gap that still fails

A cabinet hinge screw is the 105-degree case when the stile blocks a square drill and you can still brace the head. A decking screw can go either way: 90 degrees from the side, 105 degrees if a post forces the driver to lean out. The angle does not supply an impact rating. Check the impact-driver page before a 105-degree holder goes on an 18 V driver. Both angles still need a hand on the housing. The extra 15 degrees does not remove reaction torque. A slot that will not take the drill at any tilt is the flexible shaft’s job, a dedicated angle drill, or the panel coming off. The DWARAFS at £39.84 is that shaft, with a driving-only limit from one UK review. Large holes and joist boring fail both angles.

A choice with a condition

Choose 90 degrees when you can bring the drill in square. The measured options are the Milwaukee at 36 mm, the DWARA120 at 1.5 inches, and the DT20500 at 38 mm with a stated 43 Nm. Choose 105 degrees when the body must tilt off a stile and the screw is a light one you can brace. The £6.99 ColumPRO states 10 Nm. If the clearance is tighter than 36 mm and there is no room to tilt, neither angle is the tool. Bracing is on the how to use page.

Common questions

Which angle gets into a shallow gap against a panel?
The 90-degree head, if the published depth fits. Milwaukee states 36 mm. The DT20500 is stated at 38 mm. The DWARA120 states 1.5 inches front to back. A 105-degree holder needs room beside the tool. Under 36 mm square-on, the tilt will not invent a thinner gearbox.
Which angle keeps the drill off a cabinet stile?
The 105-degree head. The extra tilt pulls the body and the battery off the stile. The ColumPRO listings are that shape, and the £6.99 head states only 10 Nm. A square 90-degree head keeps the drill against the panel, which is the toe-space case.
Are 90 and 105 degrees interchangeable?
No. Ninety degrees is for depth in front of the screw. A hundred and five degrees is for clearance beside the drill. Measure the blocked direction first, then pick the angle.
Is a 105-degree head impact-rated because it is small?
No. The £6.99 ColumPRO names a drill and a cordless drill. The bit set’s impact line is about the bits. The impact-rated heads here are the DWARA120, the DT20500 and the Milwaukee 4932471274. Put a 105-degree holder on a drill-driver clutch.
Where does a flexible shaft fit if neither angle works?
When the screw is around a bend neither a square head nor a tilt can approach. In this set that is the DeWalt DWARAFS at £39.84, and one UK review says driving rather than drilling. It is not stated as impact-rated.

Related pages

Best 90 degree drill attachment

Right angle drill attachment

Right angle drill attachment: choose the type first

How to use a right angle drill attachment in a gap

Right angle attachment for your 18 V impact driver

Sources

Public UK and maker sources are listed below. Shelf prices, stars and review counts are the amazon.co.uk figures for this comparison. This page did not lab-test the attachments.

  1. HSE, PUWER overview (retrieved 22 October 2026)
  2. HSE, inspection of work equipment (retrieved 22 October 2026)
  3. GOV.UK, Supply of Machinery (Safety) Regulations 2008 (retrieved 22 October 2026)
  4. HSE, UKCA marking and work equipment (retrieved 22 October 2026)
  5. GOV.UK, product marking (retrieved 22 October 2026)
  6. Consumer Rights Act 2015 (retrieved 22 October 2026)
  7. Milwaukee Tool, Shockwave right angle attachment 4932471274 (retrieved 22 October 2026)
  8. Power Tool Centre, DeWalt DT20500 (retrieved 22 October 2026)
  9. Yandles, Milescraft Drill90PLUS (retrieved 22 October 2026)