Independent comparisons. We may earn from shop links. More info

Best 250mm circular saw blade for the job in front of you

Updated: October 2026

You want one 250 mm blade for one job, and a reason to leave the other listings. Nails in reclaimed timber, a cleaner edge than the stock blade, and a coated face are three briefs. A single best 250mm circular saw blade hides that split. The Products Compared editorial team wrote this on 16 October 2026 from UK prices, printed geometry, and UK reviews. We ran no lab cut and name no best blade in Britain. The set is the [250 mm x 30 mm circular saw blade comparison](/hub/saw-accessories/250mm-x-30mm-circular-saw-blade). A qualifying amazon.co.uk purchase can earn a commission at no extra cost to you.

You want one 250 mm blade for one job, and a reason to leave the other listings. Nails in reclaimed timber, a cleaner edge than the stock blade, and a coated face are three briefs.

Our top picks

DEWALT DeWalt DT1957 250 mm

Best overall

DEWALT DeWalt DT1957 250 mm
9.4/10about £20.79
View offer
Saxton Blades Saxton 250 mm 100T

Rank 2

Saxton Blades Saxton 250 mm 100T
9.4/10about £21.99
View offer
Tech Traders Tech Traders 250 mm 80T

Best value

Tech Traders Tech Traders 250 mm 80T
9.2/10about £13.99
View offer
On this page
  1. 1.Nails and site timber
  2. 2.A cleaner edge than the stock blade
  3. 3.Fine faces and coated board
  4. 4.The cheap pair and the three-pack

Nails and site timber

For reclaimed timber where you expect a nail, the listing that says nail-tough is the DeWalt DT1957-QZ. Titled 250 mm x 30 mm and 48 teeth, it is £20.79, rated 4.7 from 2,566 ratings. UK reviews describe hardwood cuts and nail strikes in reclaimed timber. The teeth cell says 40, and the dimensions cell says 25.4 by 25.4 cm. Leave both conflicts visible. The material cell says Shell, which we treat as a bad cell, not as the plate. No rings are included. Skip it when the arbor is 16, 20, or 25 mm and you needed a ring, or when the knife needs a printed kerf. One DIY buyer said two blades went blunt early. One kitchen fitter got about three jobs of cornice, pelmet, and plinths. It is the shortlist for hidden nails, and the wrong brief for veneer. The order of those checks is the buying guide.

A cleaner edge than the stock blade

For a finer everyday cut, once the bore is 30 mm or the ring is right, the long UK file is the Saxton TCT25080T. The cheaper twin is the Tech Traders 80-tooth at £13.99, 4.6 from 22 reviews, with the same untested fits-255 mm line. One machinist describes a fine cross-grain cut with a waste piece behind it. Choose it when the geometry is what you wanted and the Saxton price is what you are skipping.
DEWALT DeWalt DT1957 250 mm

Testsieger

DEWALT DeWalt DT1957 250 mm
9.4/10about £20.79
View offer

Fine faces and coated board

For plywood, MDF, laminated MDF, or oak, the larger fine-cut file is the Saxton TCT250100T: 100 teeth, £21.99, 4.7 from 396 reviews, positive angle, 2.6 mm kerf, 1.8 mm plate, no rpm. UK texts include laminate flooring and then a 7 by 3 metre deck, and a Rutlands owner who replaced a stock 255 mm 40-tooth blade. Life past those jobs is not measured. The -5° Saxton is £22.99, 5.0 from five reviews, same kerf and plate, rake printed as -5°. Rings listed are 16, 20 and 25 mm. The title also names 25.4 mm, which the components line does not. One UK text says laminate cut smoothly, one buyer had not tried it, and one comparison gives no detail. Use it when you pull a mitre or radial-arm saw and the printed rake is the point. Coated board is the laminate page. A 5.0 on five ratings does not outrank 396 reviews.

The cheap pair and the three-pack

The Toolzone pair is £11.57 for 40 and 60 teeth, 4.6 from 531, with 6,000 rpm printed and the bore not printed. It is scrap and pallets only after you measure the hole. Thin plates, a saw that would not clamp, and a knife that would not pass are the skips. The DeWalt three-pack at £49.59 lists 24T/48T against a teeth cell of 48, and a 1/2 inch shank bullet against 30 mm. Most early reviews are not labelled United Kingdom. One UK buyer's next set was 305 mm because this diameter was wrong.

Common questions

Which listing is for nails in reclaimed timber?
The DeWalt DT1957-QZ at £20.79 is the nail-tough title. Skip it when you need rings in the box, or when the brief is veneer and a slower 100-tooth feed. Read the 48-versus-40 conflict and the missing kerf before you pay.
What is wrong with the Saxton 80-tooth weight cell?
The TCT25080T weight cell prints 49.9 g and we leave it. One review says a 255 mm fit fell short of the deck groove. Plate thickness and rpm are not in the extract.
When is the £13.99 80-tooth blade enough?
Tech Traders is enough when you want that positive 80-tooth geometry and can accept 22 reviews. One machinist describes a fine cross-grain cut with a waste piece behind it. It is the weaker choice when you wanted the long Saxton file, or a printed plate and speed, which neither page gives you.
Which 100-tooth file is larger?
The positive Saxton at £21.99 has 4.7 from 396 reviews. The -5° blade at £22.99 has 5.0 from five, and one text says it was unused. The larger file is the stronger evidence of a clean face. The printed negative rake is the match when you pull the saw through coated board.
Why is the three-pack not the default?
Three blades at £49.59 are spare capacity only if the conflicts are acceptable: 24T/48T against a teeth cell of 48, and a 1/2 inch bullet against 30 mm. Kerf and rpm are absent. Reviews that are not labelled United Kingdom stay out. One buyer moved to 305 mm because 250 mm was the wrong diameter.
Why is 5.0 from five ratings not the winner?
Five ratings cannot show how an edge lasts, and one text is from a buyer who had not cut. The -5° blade stays a conditional choice for the saws named on its bullets. The 25.4 mm ring stays unproven because the components line does not list it.

Related pages

How to fit a circular saw blade

250mm x 30mm circular saw blade

250mm blade in a 254mm saw: depth, reach, and bore

250mm x 30mm circular saw blade: match bore, then kerf

Circular saw blade for laminate: negative or positive

Sources

Public UK sources and the amazon.co.uk listings used for this comparison; last retrieved on 17 October 2026.

  1. HSE WIS16, circular saw blades (retrieved 17 October 2026)
  2. HSE, circular rip saws (retrieved 17 October 2026)
  3. HSE, wood dust (retrieved 17 October 2026)
  4. HSE, woodworking standards (retrieved 17 October 2026)
  5. HSE, PUWER ACOP L114 (retrieved 17 October 2026)
  6. Axminster AP254TS manual (retrieved 17 October 2026)
  7. UK Workshop, 250 mm blade in a 254 mm saw (retrieved 17 October 2026)
  8. Saxton UK, negative-rake 250 mm 100 tooth blade (retrieved 17 October 2026)
  9. amazon.co.uk listings for the seven blades (retrieved 17 October 2026)