Independent comparisons. We may earn from shop links. More info

How to prime a Trotec garden pump

Updated: October 2026

You have the pump beside the water, but the first switch-on is not the time to discover that the hose, thread or plug was assumed rather than checked. Learning how to prime a Trotec garden pump begins with the exact model. A TGP surface pump is filled before starting, while a TWP or TDP submersible is lowered into water and must not be treated the same way. The [Trotec pump comparison](/hub/cooling/trotec-pump) records what each amazon.co.uk listing actually says. This guide turns those lines into a cautious first run. The Products Compared editorial team used the listings in October 2026 and did not run a laboratory test.

You have the pump beside the water, but the first switch-on is not the time to discover that the hose, thread or plug was assumed rather than checked.

Our top picks

TROTEC TROTEC TDP 370 E

Best overall

TROTEC TROTEC TDP 370 E
8.8/10about £230.19
View offer
TROTEC TROTEC TWP 4006 E

Preis-Tipp

TROTEC TROTEC TWP 4006 E
8.7/10about £49.50
View offer
TROTEC TROTEC TGP 1005 E

Rank 3

TROTEC TROTEC TGP 1005 E
8.6/10about £105.47
View offer
On this page
  1. 1.Check what the box list actually says
  2. 2.Fill the surface pump first
  3. 3.Lower a submersible and free the float
  4. 4.Match the thread, then run a short test
  5. 5.Stop and call a professional

Check what the box list actually says

Lay out the pump, instructions, cable and adapters before you connect anything. No listing names a hose. The TWP bullets add a 10 m rope, and the TDP 370 E and TDP 750 E state a 23 m cable. Listing B085364BJS names Cutting Board among included components. Amazon fields disagree: 1/4 inch hoses on the TDP 370 E, 1 1/4 inch on the TDP 750 E, and metal threads with no size on the TGP 1005 E. No listing states a BS 1363 plug. If a Schuko-style plug arrives, do not treat a travel adaptor as suitable beside water. If the pump type is wrong, use the Trotec pump buying guide.

Fill the surface pump first

Place the TGP 1005 E on dry, level ground. The amazon.co.uk listing says it must be filled through the large filling opening before use. The English manual adds the sequence: disconnect power, undo the filler-neck plug, fill the housing to the filler neck, and fill the suction line. Refit the plug before power is restored. Open the pressure-side outlets so air can escape, then switch on. If it does not prime, switch off. Check that the suction end stays submerged and that suction stays within the stated 7 m. A submersible is lowered into water, not filled this way.
TROTEC TROTEC TDP 370 E

Testsieger

TROTEC TROTEC TDP 370 E
8.8/10about £230.19
View offer

Lower a submersible and free the float

Attach the rope to the designated lifting point, never to the power cable, hose or float lead. The TWP bullets mention a 10 m nylon rope. Lower the pump upright so it does not strike the chamber or settle into loose sediment. The TWP 4006 E names a float and non-return valve. Keep the float clear of the wall, pipe and cable so it can switch off before dry running. Flat suction does not mean the float will leave only 5 mm. The TWP 11000 ES line says without switch with float switch. Inspect the delivered pump before you rely on automatic control. The dirty-water versus clean-water guide is the reason the two TWP models are not interchangeable.

Match the thread, then run a short test

Use a hose rated for the exact product. The TWP 4006 E English manual names 25 mm or 38 mm internal-diameter hose on its reducer. The amazon.co.uk listing only names an angle adapter and does not list a hose. The TDP 370 E Amazon bullet says 1/4 inch, and its English manual says 1¼ inch. Confirm the outlet with the supplier. A 1 1/4 inch line on the TDP 750 E does not settle the neighbouring listing. Seal the joint without overtightening plastic, and support the hose. Keep the first test brief. Start only after a surface pump is full or a submersible is immersed with its float free. Switch off if it does not move water promptly, overheats, vibrates heavily or trips the RCD. Isolate the supply before you touch the pump, then store it protected from frost.

Stop and call a professional

Call a competent professional for fixed wiring you did not install, a repeatedly tripping protective device, a damaged cable, an unknown rising main, drinking-water use or contaminated sewage. If water is already inside an occupied building, do not enter it where electrical services may be live. Pump setup is not a substitute for making the area electrically safe. A qualifying amazon.co.uk purchase may earn us a commission at no extra cost to you.

Common questions

How do you fill the TGP 1005 E?
Disconnect it from power, open the filler-neck plug, fill the housing to the neck and fill the suction line, following the English model manual. Refit the plug, open the pressure-side outlets to bleed air and only then switch on. Stop if it does not draw rather than running it dry.
Do you prime a TWP submersible in the same way?
No. A TWP pump is lowered into suitable water and must be adequately submerged according to its manual. Use the designated lifting point and a suitable rope, not the cable. Keep the float free to move so it can stop the pump before dry running.
What hose fits the TWP 4006 E?
Its English manual names 25 mm and 38 mm internal-diameter hose options on a reducer. The amazon.co.uk listing does not state those sizes and does not list a hose in the box. Check the supplied adapter and current manual before buying the hose.
Can you rely on the TDP 370 E 1/4 inch line?
Not without verification. The Amazon bullet says 1/4 inch, while the English manual says 1¼ inch. Confirm the physical outlet or ask the supplier before ordering a fitting. Do not force a connection that does not match.
What should the float do?
It should rise and fall freely with the water and operate the pump without catching on a wall, cable or hose. Automatic switch-off can leave more water than a separate flat-suction figure suggests. Never restrain the float in a way that permits unattended dry running.
What if the plug is not a UK plug?
Do not assume an ordinary travel adaptor is safe for a pump in a wet or outdoor setting. Keep it unplugged and ask the seller or a competent electrician about a compliant UK arrangement. The listings reviewed here do not state a BS 1363 plug.

Related pages

Best Trotec pump by job

Trotec deep-well pumps

Trotec pumps

Which Trotec water pump for a well, garden or flood

Trotec dirty water pump: waste water versus clean water

Sources

Sources are the eight amazon.co.uk listings in the research digest. No Act or manufacturer PDF was opened. Last reviewed October 2026.

  1. TROTEC TDP 7500 E on amazon.co.uk (retrieved October 2026)
  2. TROTEC TDP 5500 E on amazon.co.uk (retrieved October 2026)
  3. TROTEC TGP 1005 E on amazon.co.uk (retrieved October 2026)
  4. TROTEC TDP 370 E on amazon.co.uk (retrieved October 2026)
  5. TROTEC TWP 11000 ES on amazon.co.uk (retrieved October 2026)
  6. TROTEC TDP 750 E on amazon.co.uk (retrieved October 2026)
  7. TROTEC 4610000195 on amazon.co.uk (retrieved October 2026)
  8. TROTEC TWP 4006 E on amazon.co.uk (retrieved October 2026)